Looking to upgrade your Roman tub faucet, but don’t have an access panel? No worry, replacing a roman tub faucet without an access panel is not a difficult process. With a little bit of knowledge and the right tools, you can replace it smoothly. To know how to replace roman tub faucet with no access panel, keep reading.
You might want to replace it because it starts leaking or you want to install a new stylish roman tub faucet. Old faucets start showing issues after a certain time period. Many roman tub faucets come with an access panel. But when there is no access panel, it becomes confusing to replace. Follow the steps from the guide to complete the replacement process without any mistakes.
Start The Preparation To Replace Roman Tub Faucet
Before starting the replacement process, by doing preparation, you can save lots of time. Gather all essential tools, so when you replace the roman tub faucet, you don’t need to find tools. It will save time and avoid delays.
- Adjustable wrench
- Phillips head screwdriver
- Flathead screwdriver
- Allen wrench
- Basin wrench
- Plumber’s putty
- Teflon tape
- Bucket or towel
Did you know that access panels for Roman tub faucets can occasionally be hidden in the strangest locations, such as behind cabinetry or even below the tub itself?
It’s worthwhile to spend a brief amount of time looking about your bathroom to see if you can find it. If you do manage to locate it, the first thing to do is to stop the water flow to the fixture. But don’t worry if your search is unsuccessful. By simply shutting off your home’s main water supply, you can still move through with the replacement process.
Remove the Decorative Cap and Handle
It might be difficult to replace a Roman tub faucet, particularly if there are unexpected challenges in your path. The mysterious screw holding the handle in place is one such obstacle.
The tap assembly’s handle must first be taken off before proceeding. A screw holding the handle in place typically needs to be loosened in order to do this. Yet occasionally, this screw could be covered with a cap that’s meant to hide it.
So, what should you do if you discover a hidden screw? Be at ease! The hidden screw can be seen by just removing the cap. Carefully pry off the cap to reveal the screw by using a reliable flathead screwdriver.
You can now access the hidden screw and remove it with the right tool after removing the cover. After the screw has been taken out, be careful to carefully lift the handle and pull it away from the faucet assembly. There you have it, then! You’ve taken the first step in replacing your Roman tub tap like an expert by taking the handle off.
Remove the Old Roman Tub Faucet
- The retaining nut will be our first focus. You must first take out this tiny component, which holds your tap assembly in place. The retaining nut is located at the faucet handle’s base, which you may access after removing the handle. You’ll need a wrench or pliers to remove it because it’s typically fastened quite firmly.
- In removing the retaining nut, exercise caution to prevent damage to the tub surface or the surrounding tiles. It is obvious that you don’t want to put yourself through any unneeded repair work.
- The retaining nut may occasionally be difficult to remove due to corrosion or general wear and tear. Not to worry, we have a solution for that as well! To get it loose, just use some penetrating oil. Before attempting to remove the nut once more, apply oil all around it and wait a few minutes. Don’t forget to remove any additional screws that may be holding the tap body in place in some circumstances.
- You may now raise the old tap and slide it around a little to fully detach it after removing the retaining nut. If the old tap body is stuck, you can use a putty knife or pry bar to gently remove it from the tub.
Check also – How To Install a Pot Filler Faucet In Existing Wall?
Install New Roman Tub Faucet
- Place the new Roman tub faucet on the tub after unpacking it from the box. Ensure that the tub tap is level and correctly positioned relative to the tub. Before you take the next step, you want to be sure that everything feels and looks great.
- Screw the faucet’s retaining nut after positioning it on the tub. Never forget to hand-tighten the nut before using a wrench or pliers to thoroughly tighten it. Make sure you tighten all of the retaining nuts, as there may be more than one depending on the faucet model.
- The new Roman tub fixture’s handle should be attached. You should make sure the handle’s screw is correctly tightened. Put any rings that the tap may have in the proper positions to form a watertight seal. Always refer to the instruction booklet if you want to know where the rings should be placed. A fantastic material to stop any leaks around the tap base is the plumber’s putty.
- Attach the cold and hot water supply lines to the sink’s faucet. Turn on the water supply after giving them a thorough tightening. Before you congratulate yourself on a job well done, don’t forget to check for leaks.
Check Also – Quick and Easy Way To Get Rid of Ants in Faucet
James Lewis is a seasoned plumber and faucet enthusiast who shares his expertise on Faucetsavvy.com. With over 15 years of experience in the plumbing industry, he’s passionate about helping homeowners find the perfect faucet for their needs. He’s also dedicated to empowering DIY enthusiasts with the plumbing knowledge and skills needed to repair and maintain their faucets.